Por favor, use este identificador para citar o enlazar este ítem: http://bibdigital.epn.edu.ec/handle/15000/18828
Registro completo de metadatos
Campo DCValorLengua/Idioma
dc.contributor.authorNovoa Trávez, Fernando Efraín-
dc.contributor.authorRodríguez Flores, Juan Carlos-
dc.date.accessioned2017-10-10T19:52:27Z-
dc.date.available2017-10-10T19:52:27Z-
dc.date.issued2017-10-10-
dc.identifier.citationNovoa Trávez, F. E., & Rodríguez Flores, J. C. (2017). Diseño y construcción de un elevador una columna para autos. 134 hojas. Quito : EPN.es_ES
dc.identifier.otherT-MVE/0606/CD 8217-
dc.identifier.urihttp://bibdigital.epn.edu.ec/handle/15000/18828-
dc.descriptionEn el presente proyecto se ha diseñado y fabricado un elevador de autos de una sola columna, el cual se usará para realizar prácticas que permitan investigar y desmontar partes de automotores utilizados como material didáctico para los estudiantes tanto de pregrado como posgrado de la Facultad de Ingeniería Mecánica. Este elevador facilitará la observación de los diferentes sistemas del automotor ubicados en la parte inferior para mejorar el aprendizaje de los estudiantes. La elección de la alternativa a diseñar y fabricar se basó en el libro “Diseño Concurrente” de Carles Ribas con el método de evaluación de soluciones. Está estructurado en cuatro brazos deslizables anclados a un cilindro hidráulico que reposa en la viga principal de elevación y su base; favoreciendo el reparto de cargas siendo muy útil en todo tipo de superficies planas. El automotor se fija en los brazos del elevador de forma simétrica garantizando el equilibrio y seguridad deseada. Todo el sistema es propulsado por un sistema electrohidráulico alimentado con corriente alterna trifásica de 220 Vac. que se puede obtener de la red.es_ES
dc.description.abstractThe present project has designed and manufactured a single-column car elevator, which will be used to carry out practices that allow the investigation and dismantling of used automotive parts of teaching material for both undergraduate and postgraduate students of the Faculty of Engineering Mechanics. This lift will facilitate the observation of the different automotive systems located at the bottom to improve student learning. The choice of the alternative to design and manufacture was based on the book "Design Concurrent" by Carles Riba with the method of evaluation of solutions. This lifting system is structured in two sliding arms anchored to a hydraulic cylinder that rests on the main lifting beam and the base; favoring the distribution of loads being very useful in all types of flat surfaces. The automotor is fixed in the arms of the elevator of symmetrical form guaranteeing the balance and security wanted. The entire system is powered by an electro-hydraulic system powered by 220 V three-phase alternating current that can be obtained from the mains.es_ES
dc.description.sponsorshipZambrano Orejuela, Oscar Iván, directores_ES
dc.language.isospaes_ES
dc.publisherQuito, 2017.es_ES
dc.rightsopenAccesses_ES
dc.subjectDISEÑO DE MAQUINASes_ES
dc.subjectHIDRAULICAes_ES
dc.subjectMAQUINASes_ES
dc.titleDiseño y construcción de un elevador una columna para autoses_ES
dc.typemasterThesises_ES
Aparece en las colecciones:Tesis Maestría en Diseño, Producción y Automatización Industrial (FIM)

Ficheros en este ítem:
Fichero Descripción TamañoFormato 
CD-8217.pdf10,46 MBAdobe PDFVisualizar/Abrir


Los ítems de DSpace están protegidos por copyright, con todos los derechos reservados, a menos que se indique lo contrario.