Por favor, use este identificador para citar o enlazar este ítem: http://bibdigital.epn.edu.ec/handle/15000/19396
Título: Síntesis de un material compuesto a partir de caucho reciclado y poliuretano
Autor: Chiguano Niquinga, Alex Omar
Palabras clave: MECÁNICA DE MATERIALES
CAUCHO RECICLADO
MATERIALES COMPUESTOS
Fecha de publicación: 9-may-2018
Editorial: Quito, 2018.
Citación: Chiguano Niquinga, A. O. (2018). Síntesis de un material compuesto a partir de caucho reciclado y poliuretano. 97 hojas. Quito : EPN.
Resumen: The influence on the mechanical and thermal properties when incorporating recycled rubber’s particles as reinforcement in a thermo-plastic polyurethane matrix was analyzed. Two influence factors were analyzed: the particle size of recycled rubber (840, 500, 177 μm) and its concentration (10, 20, 25 wt%). This composite material was obtained through extrusion and injection processes. The test pieces for the trials for traction, tearing, hardness and abrasiveness were obtained from a process called die-cutting under the ASTM D412-16, D1004-13, D2240 and INEN 1924 standards, respectively. The water permeability analysis was performed by a methodology proposed by another researcher and the resistance to hydrocarbons was done using the ASTM D471 standard. A thermal characterization on the material was done through a thermo-gravimetric analysis, and it was performed some SEM microscopy to observe the adherence of the matrix and the reinforcement. On the other hand, in order to analyze the obtained results and determine the factors that influence on the mechanical properties, a statistics analysis was performed. The results show that incorporating recycled rubber particles modified the mechanical properties of the material; improving the elasticity and hardness properties, but decreasing traction, tearing and abrasiveness resistance; however, water permeability, and hydrocarbons solubility weren’t affected.
Descripción: Se analizó la influencia en las propiedades mecánicas y térmicas al incorporar como refuerzo partículas de caucho reciclado (PCR) en una matriz de poliuretano termoplástico. Se analizó la influencia de dos variables; el tamaño de partícula del caucho reciclado (840, 500, 177 μm) y la concentración del mismo (10, 20, 25 wt%). El material compuesto se obtuvo mediante procesos de extrusión e inyección. Las probetas para los ensayos de tracción, desgarre, dureza y abrasión se obtuvieron por troquelado según lo establecido en las normas ASTM D412-16, D1004-13, D2240 e INEN 1924, respectivamente. El análisis de permeabilidad al agua se realizó con la metodología propuesta en otra investigación y resistencia a hidrocarburos mediante la norma ASTM D471. Además, se realizó una caracterización térmica del material mediante un análisis termogravimétrico, y para observar la adherencia matriz-refuerzo se realizaron microscopías SEM. Para analizar los resultados obtenidos y determinar la influencia de las variables en las propiedades mecánicas se realizó un análisis estadístico. La incorporación de PCR modificó las propiedades mecánicas de material; mejorando el módulo de elasticidad y la dureza, pero disminuyeron la resistencia a la tracción, desgarre y abrasión, la permeabilidad al agua y la solubilidad en hidrocarburos no se vieron afectadas.
URI: http://bibdigital.epn.edu.ec/handle/15000/19396
Tipo: bachelorThesis
Aparece en las colecciones:Tesis Mecánica (IM)

Ficheros en este ítem:
Fichero Descripción TamañoFormato 
CD-8783.pdf2,82 MBAdobe PDFVisualizar/Abrir


Los ítems de DSpace están protegidos por copyright, con todos los derechos reservados, a menos que se indique lo contrario.